Missing info from Pink2 manual

Tips & tricks, working results, technical support
Post Reply
Sturphy
User Level I
User Level I
Posts: 15
Joined: Thu Aug 25, 2011 8:06 am

Missing info from Pink2 manual

Post by Sturphy » Wed Apr 11, 2018 6:42 am

Any official documentation on these controls?
Pink2 controls.png
Pink2 controls.png (13.74 KiB) Viewed 565 times

User avatar
Sheikyearbouti
Member
Member
Posts: 319
Joined: Wed Feb 16, 2011 6:49 pm
Location: London, UK
Contact:

Re: Missing info from Pink2 manual

Post by Sheikyearbouti » Wed Apr 11, 2018 12:25 pm

These are a HPF, LPF and a BPF. Measuring the plug-in I find the following:

HPF is at about 55Hz (it is -3dB at that point, which is how you measure the cut-off frequency of such filters)
LPF is at 12kHz (you start losing some HF from about 4k but very gradually)
BPF has the cut-off frequencies around 100Hz and 12kHz.

You can actually have all of them on - so these are additive filters...
--
Nikolay Georgiev
http://georgievsound.com/

Sturphy
User Level I
User Level I
Posts: 15
Joined: Thu Aug 25, 2011 8:06 am

Re: Missing info from Pink2 manual

Post by Sturphy » Thu Apr 12, 2018 12:48 am

Thanks. Any idea where in the signal chain they happen? Before the preamp?

User avatar
Sheikyearbouti
Member
Member
Posts: 319
Joined: Wed Feb 16, 2011 6:49 pm
Location: London, UK
Contact:

Re: Missing info from Pink2 manual

Post by Sheikyearbouti » Thu Apr 12, 2018 1:19 pm

I'll ask the guys that made the routing decisions (and forward an add-on text for the manual), but my assumption is that they will be stuck to the EQ section so that the impulse responses can be coalesced to reduce latency and CPU load. I'll post again here in case I am mistaking this, but it must be that way.
--
Nikolay Georgiev
http://georgievsound.com/

User avatar
Sheikyearbouti
Member
Member
Posts: 319
Joined: Wed Feb 16, 2011 6:49 pm
Location: London, UK
Contact:

Re: Missing info from Pink2 manual

Post by Sheikyearbouti » Thu Apr 12, 2018 2:11 pm

Hey man, to confirm, this is the actual signal flow in the strip:

Input gain -> preamp -> filters + EQ -> compressor -> output gain
--
Nikolay Georgiev
http://georgievsound.com/

kenbobplus3db
User Level VIII
User Level VIII
Posts: 81
Joined: Wed Jul 27, 2016 9:58 pm

Re: Missing info from Pink2 manual

Post by kenbobplus3db » Fri Apr 13, 2018 11:20 pm

Did the insane mode make it into the Pink2 ports of 2412 and 7236?

Sturphy
User Level I
User Level I
Posts: 15
Joined: Thu Aug 25, 2011 8:06 am

Re: Missing info from Pink2 manual

Post by Sturphy » Sat Apr 14, 2018 9:08 am

Sheikyearbouti wrote:
Thu Apr 12, 2018 2:11 pm
Hey man, to confirm, this is the actual signal flow in the strip:

Input gain -> preamp -> filters + EQ -> compressor -> output gain
Thank you!

User avatar
babiuk
Vip Member
Vip Member
Posts: 378
Joined: Tue Oct 19, 2010 11:16 am

Re: Missing info from Pink2 manual

Post by babiuk » Sun Apr 15, 2018 1:53 pm

NO official response from AA????
Mac Pro 5,1 / 6-core Intel Xeon / 16 GB Ram / El Capitan / Reaper / H******* Mixbuss

AcusticaPress
User Level VI
User Level VI
Posts: 62
Joined: Mon Mar 17, 2014 1:58 am

Re: Missing info from Pink2 manual

Post by AcusticaPress » Mon Apr 16, 2018 9:33 am

Sheikyearbouti wrote:
Wed Apr 11, 2018 12:25 pm
These are a HPF, LPF and a BPF. Measuring the plug-in I find the following:

HPF is at about 55Hz (it is -3dB at that point, which is how you measure the cut-off frequency of such filters)
LPF is at 12kHz (you start losing some HF from about 4k but very gradually)
BPF has the cut-off frequencies around 100Hz and 12kHz.

You can actually have all of them on - so these are additive filters...
Hey babiuk, these values and the provided above information are correct. They have also been sent to the office to be included in the manual.
(Sheikyearbouti here)
Acustica Press
Acusticaudio SRL
www.acustica-audio.com

Post Reply